Vertex Diagnostics UltraTRAK Manual do Proprietário

Version 1.0 2010/08311-4277100-007MANUALOWNER'SBlood Glucose Monitoring System

10Display Screen Test Result Ketone Warning Error Message Memory Mode Symbol Control Solution Mode Measuring Mode Blood Drop Symbol Test Strip Symb

11Test Strip Test results might be wrong if the contact bar is not fully inserted into the test slot.Attention!The front side of the test strip should

12Setting the Meter Before using your meter for the rst time or if you change the meter battery, you should check and update these settings. Make sur

132. Setting the time format Press the M button to select the desired time format --- 12h or 24h. Press SET.3. Setting the time With the hour ashing,

145. Setting the reminder alarmYou may set up any or all of the reminder alarms (1-4). The meter displays “On” or “OFF” and , press the M button to

15THE FOUR MEASURING MODES The meter provides you with four modes for measuring General, AC, PC and QC.2. Press the M button to switch between General

16Control Solution Testing UltraTRAK Control Solution contains a known amount of glucose that reacts with test strips and is used to ensure your meter

173. Apply Control Solution.Shake the control solution vial thoroughly before use. Squeeze out a drop and wipe it off, then squeeze ano

18Out-of-range results If you continue to have test results fall outside the range printed on the test strip vial, the meter and strips may not be wor

19GETTING A BLOOD SAMPLE Overview of the Lancing DeviceSetting up the Lancing DeviceIf your lancing device differs from the one shown above, please r

Dear UltraTRAK Ultimate System Owner:Thank you for purchasing the UltraTRAK Ultimate Blood Glucose Monitoring System. This manual provides

203. Twist the protective disk off the lancet. 4. Replace the cap by aligning the arrow on the cap with the release button. 5. Select the depth of

21Preparing the Puncture Site.Stimulating blood perfusion by rubbing the puncture site before blood extraction has a signicant inuence on the glucos

22Performing a Blood Glucose Test 1. Insert the Test Strip to Turn on the MeterWait for the meter to display the test strip and blood drop

234. Apply the Sample Hold the blood drop to touch the absorbent hole of the test strip. Blood will be drawn in and after the conrmation window

245.Read the ResultThe result of your blood glucose test will appear after the meter counts to 0. This reading will automatically be stored in

25METER MEMORY Reviewing Test Results The meter stores the 1000 most recent blood glucose test results along with respective dates and

26Reviewing Blood Glucose Day Average Results 1. Press and release the M button When appears on the display, keep pressing the M button for 3 seconds

272. Exit the meter memory Keep pressing the M button and the meter will turn off after display-ing the last test result. Any time you wish to ex

28Downloading Results onto a Computer You can use the meter with a USB cable and the Health Care Software System to view your test results on your per

29MAINTENANCE Battery Your meter comes with two1.5V AAA size alkaline batteries.1. The symbol appears along with display messages: The meter

IMPORTANT SAFETY PRECAUTIONSREAD BEFORE USE1. Use the device only for the intended use described in this manual.2. Do not use accessories which are no

30 Replacing the batteries does not affect the test results stored in memory. As with all small batteries, these batteries should be k

31Caring for Your Meter To avoid the meter and test strips attracting dirt, dust or other contaminants, please wash and dry your hands thor

32Important Control Solution Information Use only UltraTRAK control solutions with your meter. Do not use the control solution beyond the ex

33SYSTEM TROUBLESHOOTING If you follow the recommended action but the problem persists, or error messages other than the ones below appear,

34Error Messages MESSAGE WHAT IT MEANS WHAT TO DOAppears when the batteries cannot provide enough power for a test.Replace the batteries immediately

35Troubleshooting 1. If the meter does not display a message after inserting a test strip:2. If the test does not start after applying the sample:3. I

36DETAILED INFORMATION Reference Values Blood glucose monitoring plays an important role in diabetes control. A long-term study showed that maintainin

37Comparing Meter and Laboratory Results The meter provides you with plasma equivalent results. The result you obtain from your meter may differ

38References *2: Surwit, R.S., and Feinglos, M.N.: Diabetes Forecast (1988), April, 49-51.*3: Sacks, D.B.: “Carbohydrates. “ Burtis, C.A., and Ashwood

39SPECIFICATIONS Model No.: UTUBGMDimension & Weight: 96 (L) x 61 (W) x 26 (H) mm, 67.2 g Power source: Two 1.5V AAA alkaline batteries Display: L

TABLE OF CONTENTSIMPORTANT SAFETY PRECAUTIONS 3BEFORE YOU BEGIN 6Important Information 6Intended Use 7Test Principle 7Contents of System 8Meter

40MEMO

Battery 29 Caring for Your Meter 31Caring for Your Test Strips 31Important Control Solution Information 32SYSTEM TROUBLESHOOTING 33Result Read

6Important Information Severe dehydration and excessive water loss may cause readings ►which are lower than actual values. If you believe you are suf

7Intended Use This system is intended for use outside the body (in vitro diagnostic use) by people with diabetes at home and by health care profession

8Contents of System Your new UltraTRAK Ultimate system kit includes:For replacing test strips, control solutions, and sterile lancets please contact y

9Meter Overview TEST STRIP EJECTOREject the used strip by pushing this button up. DISPLAY SCREEN M BUTTONEnter the meter memory and silence a remind